Universal AEM V2 Water/Methanol Injection Kit without Tank(Internal MAP)

0 Review(s) Write a Review

Your Price: $496.95

Retail Price:$553.00

Your Savings:$56.05(10%)

Part Number: AEM-30-3302

The item you are trying to purchase is currently out of stock.
Please enter your name, email, and phone number below.
We will contact you as soon as this product is available.

Name: *

Email: *

Phone: *

Verification: *

Type the word above...

Quantity

Description

Fits:
Universal

Description:

THIS PRODUCT MAY BE USED SOLELY ON VEHICLES USED IN SANCTIONEDCOMPETITION WHICH MAY NEVER BE USED UPON A PUBLIC ROAD OR HIGHWAY,UNLESS PERMITTED BY SPECIFIC REGULATORY EXEMPTION (VISIT THE EMISSIONS PAGE AT HTTP://WWW.SEMASAN.COM/EMISSIONS FOR STATE BY STATEDETAILS. INSTALLERS/USERS LOCATED OUTSIDE THE UNITED STATES SHOULD ACTIN ACCORDANCE WITH THEIR LOCAL LAWS AND REGULATIONS.

IT IS THE RESPONSIBILITY OF THE INSTALLER AND/OR USER OF THIS PRODUCTTO ENSURE THAT IT IS USED IN COMPLIANCE WITH ALL APPLICABLE LAWS ANDREGULATIONS, AND THIS PRODUCT MUST NOT BE PURCHASED IF THE INTENT IS TOUSE IT IN AN UNLAWFUL MANNER.

Water/methanol injection for gas engines is a proven means foreffectively reducing engine inlet air temperatures and suppressingharmful detonation on forced induction and high compression naturallyaspirated (NA) race engines. This allows racers to reliably increaseboost and advance ignition timing without using high-octane racingfuel for power gains of up to 20%. AEM s Water/Methanol InjectionSystems utilize the most robust hardware combined with more advancedfeatures than any other comparably priced water/methanol system.

The on-demand progressive controller in AEM s Boost Dependent PN30-3302tank-less Water/Methanol Injection kit bases injection flow on manifoldpressure using an on-board MAP sensor (up to 35 PSI of boost) to ensurethe proper amount of water/methanol injection at all points along anengine s power curve.

AEM s engineers spent extensive time developing the controller s flowcontrol strategy for a more linear flow output delivery. This meansthat the flow delivery better matches an engine s need forwater/methanol injection, which further optimizes charge air coolingand detonation control.

The new controller design features large, turn-resistant knobs andlarger numbering to easily set accurate start and full activationpoints, with covered status LED and test buttons for added splashresistance. A plug is integrated into the controller housing for matingto the redesigned wiring harness s positive-lock connector. The BoostDependent controller housing has a molded-in, barbed nipple to accept aboost hose and a wiring legend on the back, integrated fuse and moldedmounting tabs.

AEM s Boost Dependent Water/Methanol Injection kit s wiring harness isterminated with a positive-lock connector on one end and hascolor-coded wires to ease installation. Both the power and ground wiresfor the pump are included in the harness which simplifies the wiringprocess and eliminates any chance of the pump accidentally activatingfrom a short in the system. An additional wire is included for addingan optional on/off solenoid to stop fluid flow when the system isinactive.

Boost Dependent controller features on-board MAP sensor with largeadjustment knobs, integrated plug for harness connection, integratedfuse, covered status light and test button for enhanced splashresistance and mounting tabs
Wiring harness is terminated with a positive-lock connector on one endwith color-coded wires to ease installation, power and ground wires forthe pump and additional wire for optional on/off fluid solenoid
Boost Safe failsafe output included (for complete failsafe under allconditions, see Water/Methanol Failsafe Device)
Internally-bypassed water/methanol injection pump does not cycle on anoff and provides quiet, smooth operation. It features robustconstruction including integral hose fittings, EPDM seals and aSantoprene diaphragm that provides consistent and reliable fluiddelivery
Precision-machined billet-aluminum injector with integral check valve
Three interchangeable injector nozzles to cover a wide variety of HPlevels (250cc/min, 500 cc/min & 1,000cc/min)
Tank-less 35 PSI Boost Dependent gas water/methanol system (AEM Part#30-3300 includes controller with on-board MAP sensor and 1 gallon tank)
20 feet of injection tubing included
LED dash light for system status and low fluid warning

Universal AEM V2 Water/Methanol Injection Kit without Tank(Internal MAP)

Browse Similar Items